Recent questions in IES Conventional-2

0 votes

0 answers

Determine the torque that can be transmitted by a single-plate clutch and the axial thrust.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the axial thrust to be provided by springs

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What will be the maximum torque that the welded joint can sustain if the permissible shear stress

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

List two temporary fasteners and explain the working of one of these.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the size of the weld required for static loading in the eccentrically loaded weld as show in the figure below

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Suggest most suitable and cheapest material for the following

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What will be the maximum torque that the welded joint can sustain if the permissible shear stress

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What is the amount of clearance and the need for the clearance between nominal diameter of the rivet and rivet hole?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Calculate the minimum amount of overlapping by the angle section on the gusset plate

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the minimum lengths L1 and L2 that will cause the angle to carry the maximum allowable axial load.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the weld size if shear stress in the same is not to exceed 140 MPa.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

The welds are produced by shielded arc welding process with a permissible strength of 15 kgf / mm2.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

The proportions of a common rivet and the guide lines for designing a single riveted lap joint are given:

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the ratio of these limiting loads

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

calculate the dimensions of the screw and the length of the nut

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the force on the lever end required while raising and lowering the load.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine shear stress on the tie rod due to above torque.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What is the flaw in the above design?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Acme screw threads?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

1 answer

Why is taper provided in a cotter? What is the normal value of taper in cotter joint?

asked Nov 13, 2017 in MD by chandu (215k points)

Page:

« prev
1
...
33
34
35
36
37
38
39
40
41
...
54
next »

Recent questions in IES Conventional-2

...