Recent questions in IES Conventional-2

0 votes

0 answers

State the standard value of pulley groove angle and the minimum recommended angle of arc of contact for a V-belt

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the number of ropes required and rope diameter. Calculate also the length of each rope

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Under what conditions is the gear drive preferred over belt drive?

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the width of a 9.75 mm thick leather belt required to transmit 20 HP from a motor running at 900 RPM

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Why does torque transmitted by a belt drive decrease at high speeds ?

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

What is the maximum power transmitted without belt slipping in any one of the pulleys?

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the width of belt required if the permissible belt tension = 16 kgf / cm width.

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the number of ropes required.

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

How much power would the drive transmit adopting either of the alternatives?

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Briefly explain the role of idle gears in a simple gear train, with the help of neat sketches.

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Check the gear for wear if the surface endurance limit is 600MPa

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the necessary module and width of face to give greatest number of teeth.

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Explain the following terms with the help of a neat sketch pertaining to the Helical gears

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Calculate the bearing reactions for the gear when the pinion rotates clockwise.

asked Nov 14, 2017 in MD by chandu (215k points)

0 votes

0 answers

Under what conditions is the gear drive is preferred over belt drive

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Mention the factors necessary for the design of spur gears.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the tooth loads and bearing reactions for the shaft shown in figure used to transmit power

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Calculate the power that can be transmitted safely by a pair of spur gears with the data given below.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

The hydrostatic conical thrust bearing is shown in the figure. Show that the load carrying capacity of the bearing

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find (a) sommerfeld number (b) minimum film thickness (c) frictional torque

asked Nov 13, 2017 in MD by chandu (215k points)

Page:

« prev
1
...
31
32
33
34
35
36
37
38
39
...
54
next »

Recent questions in IES Conventional-2

...