Recent questions tagged welded&riveted-joints

0 votes

0 answers

The following two figure show welded joints (XXX indicated welds)

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

Match List-I (Types of joints) and List – II (An element of the joint)

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

Which one of the following structural joints with 10 rivets and same size of plate and material will be most efficient?

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

The most efficient riveted joint possible is one which would be as strong in tension, shear an bearing as

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

Match List – I (Type of Joints) and List –II (Made of Joining members)

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

The frictional torque for square thread at mean radius while raising load is given be

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

The frictional torque for square thread at mean radius while raising load is given be

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

The frictional torque for square thread at mean radius while raising load is given be

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

The frictional torque for square thread at mean radius while raising load is given be

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

In a flat collar pivot bearing, the moment due to friction is proportional to

asked Dec 19, 2017 in md by chandu (215k points)

0 votes

0 answers

Which of the following stresses are associated with the tightening of a nut on a stud?

asked Dec 18, 2017 in md by chandu (215k points)

0 votes

0 answers

What will be the maximum torque that the welded joint can sustain if the permissible shear stress

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

List two temporary fasteners and explain the working of one of these.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the size of the weld required for static loading in the eccentrically loaded weld as show in the figure below

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Suggest most suitable and cheapest material for the following

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What will be the maximum torque that the welded joint can sustain if the permissible shear stress

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What is the amount of clearance and the need for the clearance between nominal diameter of the rivet and rivet hole?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Calculate the minimum amount of overlapping by the angle section on the gusset plate

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the minimum lengths L1 and L2 that will cause the angle to carry the maximum allowable axial load.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the weld size if shear stress in the same is not to exceed 140 MPa.

asked Nov 13, 2017 in MD by chandu (215k points)

Page:

...