Login
Remember
Register
Adapala's Forum
Home
Questions
Unanswered
Tags
Categories
Users
Ask a Question
Adapala
IES GS
Ask a Question
Recent questions in TOM
0
votes
0
answers
Determine the horizontal distance covered until the particle reached a point 30 m below its original elevation.
asked
Oct 27, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
governors
0
votes
0
answers
Determine the stiffness of the spring and the maximum speed of the governor.
asked
Oct 27, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
governors
0
votes
0
answers
Discuss criteria of stability for spring controlled governors.
asked
Oct 27, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
governors
0
votes
0
answers
Presume that all masses including the balance mass rotate in the same plane.
asked
Oct 27, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
balancing
0
votes
0
answers
Define interference in involute gears.
asked
Oct 27, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
gears
0
votes
0
answers
State the factor affecting the amount of draught produced in the boiler
asked
Oct 26, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
boilers
0
votes
0
answers
Draw a self explanatory sketch of a Sigma mechanical comparator.
asked
Oct 26, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
mechanical-vibrations
0
votes
0
answers
Draw the free body diagram of the driven gear and show all the forces acting on it.
asked
Oct 26, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
gear-trains
0
votes
0
answers
Compare the deflection of the shaft at 1500 rpm in the two cases.
asked
Oct 26, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
static-loading
0
votes
0
answers
State the main disadvantage of this type follower motion.
asked
Oct 26, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
cams
0
votes
0
answers
Find out balancing condition of the engine for primary and secondary effects.
asked
Oct 26, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
balancing
0
votes
0
answers
Which type of epicyclic gear train is used for rear wheel drive of automotive trucks?
asked
Oct 24, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2010
tom
kinematics
0
votes
0
answers
What is a quick-return mechanism?
asked
Oct 24, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2010
tom
kinematics
0
votes
0
answers
What is the difference between centrifugal and inertia type of governors?
asked
Oct 24, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2010
tom
governors
0
votes
0
answers
The surface of a nut moving over a threaded bolt?
asked
Oct 24, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2010
tom
cams
0
votes
1
answer
Velocity and acceleration of sliding of bar through the swivel
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2013
tom
kinematics
0
votes
1
answer
Determine the (i) stiffness of each spring (ii) dynamic force transmitted to the floor
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2013
tom
mechanical-vibrations
0
votes
0
answers
why flywheels of multi-cylinder inline engines are relatively smaller than that of single cylinder engine?
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2013
tom
flywheels
0
votes
1
answer
Determine the stiffness of the spring and the maximum speed of the governor.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
governors
0
votes
1
answer
Presume that all masses including the balance mass rotate in the same plane.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
balancing
Page:
1
2
3
4
next »
Ask a question:
Welcome to Q&A discussion forum, where you can ask questions and receive answers from other members of the community.
Categories
All categories
GATE
(2k)
IES Objectives-1
(1.8k)
IES Objectives-2
(2.8k)
IES Conventional-1
(655)
IES Conventional-2
(1.1k)
IAS Mains
(633)
production
(83)
IM&OR
(69)
FM&Compressible
(18)
HT
(42)
TD
(48)
power plant
(73)
IC engines
(58)
RAC
(36)
SOM&MD
(63)
TOM
(73)
Engg Mechanics
(17)
Material Science
(53)
IAS Prelims
(1.2k)
IES GS & Aptitude
(61)
Engineering Mathematics
(1)
Most popular tags
ies-objectives-2
gate
ies-objectives-1
production
iasprelims
ies-conventional-2
im&or
tom
fm
td
som
ies-conventional-1
iasmains
md
ppe
2009
2008
2014
2007
2005
Recent questions in TOM
10.4k
questions
274
answers
26
comments
15.3k
users
...