Login
Remember
Register
Adapala's Forum
Home
Questions
Unanswered
Tags
Categories
Users
Ask a Question
Adapala
IES GS
Ask a Question
Recent questions in IAS Mains
0
votes
0
answers
Give the composition and the maximum temperature at which eutectoid and eutectic are formed.
asked
Oct 24, 2017
in
Material Science
by
chandu
(
215k
points)
iasmains
2010
material-science
heat-treatment-process
0
votes
0
answers
What is the difference between centrifugal and inertia type of governors?
asked
Oct 24, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2010
tom
governors
0
votes
0
answers
The surface of a nut moving over a threaded bolt?
asked
Oct 24, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2010
tom
cams
0
votes
0
answers
Why is the former preferred to the latter?
asked
Oct 24, 2017
in
SOM&MD
by
chandu
(
215k
points)
iasmains
2010
som&md
bending-stress
0
votes
0
answers
What is the maximum value of torque T
asked
Oct 24, 2017
in
SOM&MD
by
chandu
(
215k
points)
iasmains
2010
som&md
principal-stresses
0
votes
1
answer
Velocity and acceleration of sliding of bar through the swivel
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2013
tom
kinematics
0
votes
1
answer
Determine the (i) stiffness of each spring (ii) dynamic force transmitted to the floor
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2013
tom
mechanical-vibrations
0
votes
0
answers
why flywheels of multi-cylinder inline engines are relatively smaller than that of single cylinder engine?
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2013
tom
flywheels
0
votes
1
answer
Determine the stiffness of the spring and the maximum speed of the governor.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
governors
0
votes
1
answer
Presume that all masses including the balance mass rotate in the same plane.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
balancing
0
votes
0
answers
Explain the phenomena of surge and choking in centrifugal compressors.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2012
tom
gears
0
votes
1
answer
Find the speed ratio of the gear train.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
gear-trains
0
votes
1
answer
Compare the deflection of the shaft at 1500 rpm in the two cases.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
static-dynamic-balancing
0
votes
0
answers
State the main disadvantage of this type follower motion
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2016
tom
cams
0
votes
1
answer
Find out balancing condition of the engine for primary and secondary effects.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2011
tom
balancing
0
votes
0
answers
What is the damping ratio of the foundation?
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2016
tom
mechanical-vibrations
0
votes
0
answers
Determine the mass of the flywheel of radius of gyration of 400 mm.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2016
tom
flywheels
0
votes
0
answers
Determine the speed of the output shaft and the direction of rotation of the output shaft.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2016
tom
gear-trains
0
votes
1
answer
The fall in the speed of the flywheel after riveting.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2015
tom
flywheels
0
votes
1
answer
The displacement and velocity at the time equal to one second.
asked
Oct 23, 2017
in
TOM
by
chandu
(
215k
points)
iasmains
2015
tom
mechanical-vibrations
Page:
« prev
1
...
5
6
7
8
9
10
11
12
13
...
32
next »
Ask a question:
Welcome to Q&A discussion forum, where you can ask questions and receive answers from other members of the community.
Categories
All categories
GATE
(2k)
IES Objectives-1
(1.8k)
IES Objectives-2
(2.8k)
IES Conventional-1
(655)
IES Conventional-2
(1.1k)
IAS Mains
(633)
production
(83)
IM&OR
(69)
FM&Compressible
(18)
HT
(42)
TD
(48)
power plant
(73)
IC engines
(58)
RAC
(36)
SOM&MD
(63)
TOM
(73)
Engg Mechanics
(17)
Material Science
(53)
IAS Prelims
(1.2k)
IES GS & Aptitude
(61)
Engineering Mathematics
(1)
Most popular tags
ies-objectives-2
gate
ies-objectives-1
production
iasprelims
ies-conventional-2
im&or
tom
fm
td
som
ies-conventional-1
iasmains
md
ppe
2009
2008
2014
2007
2005
Recent questions in IAS Mains
10.4k
questions
274
answers
26
comments
14.7k
users
...