Recent questions tagged ies-conventional-2

0 votes

0 answers

Mention the factors necessary for the design of spur gears.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the tooth loads and bearing reactions for the shaft shown in figure used to transmit power

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Calculate the power that can be transmitted safely by a pair of spur gears with the data given below.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

The hydrostatic conical thrust bearing is shown in the figure. Show that the load carrying capacity of the bearing

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find (a) sommerfeld number (b) minimum film thickness (c) frictional torque

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What are common modes of failure of rolling element bearings.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Name the four principal types of roller bearings.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the bearing characteristic number for l/d =1.5 and absolute viscosity 0.0225 kg/ms.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

In journal bearings distinguish between “Bearing characteristic number” and “Bearings Modulus”

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Using Raymond’s & Boyd table given at the end of the problem, determine the sommerfeld Number

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Mention three different methods used to prevent an antifriction bearing from sliding axially in a shaft

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

An antifriction bearing used in a gear box has a specification 6108. What do the numbers 6, 1 and 08 signify?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Why are antifriction bearings not used at very high speeds?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the coefficient of friction using McKee equation

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What are extreme pressure lubricants? What are the main additives and how do they act?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

What do you understand by basic static low rating of a bearing?

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Determine the pipe size for (i) oil inlet if the maximum velocity of flow is 1.25 m/sec and (ii) oil drain

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Select a suitable ball-bearing subjected to following loads:

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Calculate the time required to bring the output shaft to the rated speed from rest.

asked Nov 13, 2017 in MD by chandu (215k points)

0 votes

0 answers

Find the required axial force to develop a maximum pressure of 0.65 MPa.

asked Nov 13, 2017 in MD by chandu (215k points)

Page:

« prev
1
...
32
33
34
35
36
37
38
39
40
...
54
next »

...