Login
Remember
Register
Adapala's Forum
Home
Questions
Unanswered
Tags
Categories
Users
Ask a Question
Adapala
IES GS
Ask a Question
Recent questions in production
0
votes
0
answers
For a negative rake tool, the specific cutting pressure is smaller than that for
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
A ‘Dynamometer’ is a device used for the measurement of
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
Match List I(Cutting tool material) with List II(Major characteristic constituent)
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
In ASA system, if the tool nomenclature is 8-6-5-10-15-2-mm, then the side rake angle will be
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
For achieving a specific surface finish in single point turning, the most important factor to be controlled is
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
Tool life in the case of a grinding wheel is the time
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
If the chip-tool contact length is reduced slightly by grinding the tool face, then
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1993
production
machining-machine-tool-operation
0
votes
0
answers
In gear hobbing
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Gear burnishing is process for
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Gear lapping
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Tail stock set over method of taper turning is preferred for
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Which of the machine tools can be used for boring
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Feed gear box for a screw cutting lathe is designed on the basis of
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Vitrified bond is preferred for thin
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
A drill for drilling deep holes in Aluminum should have
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
In metal cutting use of low feeds and high cutting speeds is desired when the objective is
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Which of the following statement is incorrect with reference of lathe cutting tools?
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Tool life in generally specified by
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
 
machining-machine-tool-operation
0
votes
0
answers
Ease of machining is primarily judged by
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
0
votes
0
answers
Tool life is generally better when
asked
Dec 23, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
1992
production
machining-machine-tool-operation
Page:
« prev
1
...
17
18
19
20
21
22
23
24
25
...
36
next »
Ask a question:
Welcome to Q&A discussion forum, where you can ask questions and receive answers from other members of the community.
Categories
All categories
GATE
(2k)
IES Objectives-1
(1.8k)
IES Objectives-2
(2.8k)
tom
(488)
md
(417)
som
(393)
material science
(345)
production
(703)
im&or
(472)
robotics
(1)
mechatronics
(4)
engg mechanics
(5)
IES Conventional-1
(655)
IES Conventional-2
(1.1k)
IAS Mains
(633)
IAS Prelims
(1.2k)
IES GS & Aptitude
(61)
Engineering Mathematics
(1)
Most popular tags
ies-objectives-2
gate
ies-objectives-1
production
iasprelims
ies-conventional-2
im&or
tom
fm
td
som
ies-conventional-1
iasmains
md
ppe
2009
2008
2014
2007
2005
Recent questions in production
10.4k
questions
274
answers
26
comments
15.3k
users
...