Login
Remember
Register
Adapala's Forum
Home
Questions
Unanswered
Tags
Categories
Users
Ask a Question
Adapala
IES GS
Ask a Question
Recent questions tagged 2002
0
votes
0
answers
In rolling a strip between two rolls, the position of the neutral point in are of contact does not depends on
asked
Dec 22, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
2002
production
metal-forming
sheet-metal-operations
0
votes
0
answers
In rolling operation the maximum draft is given by (R = Radius of roll, coefficient of friction
asked
Dec 22, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
2002
production
0
votes
0
answers
Consider the following statements related to piercing and blanking
asked
Dec 22, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
2002
production
metal-forming
sheet-metal-operations
0
votes
0
answers
Match List – I (Parts) with List – II (Manufacturing processes)
asked
Dec 22, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
2002
production
metal-forming
sheet-metal-operations
0
votes
1
answer
Consider the following steps involved in hammer forging a connecting rod from bar stock
asked
Dec 22, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
2002
production
metal-forming
sheet-metal-operations
0
votes
0
answers
In casting process, the mould or core attains maximum strength.
asked
Dec 22, 2017
in
production
by
chandu
(
215k
points)
ies-objectives-2
2002
production
metal-casting
0
votes
0
answers
While calculating the stress induced in a closed coil helical spring, Wahl’s factor must be considered to account for
asked
Dec 21, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
springs
0
votes
0
answers
When a helical compression spring is cut into two equal halves, the stiffness of each of the resulting springs will be
asked
Dec 21, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
springs
0
votes
0
answers
If P is the pitch of a square theread, then the depth of thread d is given by
asked
Dec 21, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
power-screws
0
votes
0
answers
A screw jack is said to be self – locking if its efficiency is
asked
Dec 21, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
power-screws
0
votes
0
answers
A cotter joint is used when no relative motion is permitted between the rods joined by the cotter
asked
Dec 21, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
coupling-cotters-belt&chain-drives
0
votes
0
answers
The length of the belt in the case of a cross-belt drive is given in terms of
asked
Dec 21, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
coupling-cotters-belt&chain-drives
0
votes
0
answers
Which one of the following is not a friction clutch?
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
brakes-clutches-ropes
0
votes
0
answers
If the bending moment diagram is a rectangle, it indicates that the beam is loaded by
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
gears
0
votes
0
answers
A. Unwin’s formula B. Wahl factor C. Reynold’s equation D. Lewis form factor
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
gears
0
votes
0
answers
Match List – I (Bearings) with List – II (Load type)
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
bearings-shafts-axles&keys
0
votes
0
answers
Tapered roller bearings are sensitive to the tightening between
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
bearings-shafts-axles&keys
0
votes
0
answers
A Woodruff key is an easily adjustable key.
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
bearings-shafts-axles&keys
0
votes
0
answers
The power that can be transmitted by the new shaft is
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
bearings-shafts-axles&keys
0
votes
0
answers
An eccentrically loaded riveted joint is shown with 4 rivets at P, Q, R and S.
asked
Dec 20, 2017
in
md
by
chandu
(
215k
points)
ies-objectives-2
2002
md
bolted-joints&welded&riveted-joints
Page:
« prev
1
...
4
5
6
7
8
9
10
11
12
...
22
next »
Ask a question:
Welcome to Q&A discussion forum, where you can ask questions and receive answers from other members of the community.
Categories
All categories
GATE
(2k)
IES Objectives-1
(1.8k)
IES Objectives-2
(2.8k)
IES Conventional-1
(655)
IES Conventional-2
(1.1k)
IAS Mains
(633)
IAS Prelims
(1.2k)
IES GS & Aptitude
(61)
Engineering Mathematics
(1)
Most popular tags
ies-objectives-2
gate
ies-objectives-1
production
iasprelims
ies-conventional-2
im&or
tom
fm
td
som
ies-conventional-1
iasmains
md
ppe
2009
2008
2014
2007
2005
10.4k
questions
274
answers
26
comments
14.6k
users
...